NCL SW-PU V Single-Component Flexible Injection Resin

NCL SW-PU V Single-Component Flexible Injection Resin Single-component Injection Resin NCL Injection Resin


PRODUCT DESCRIPTION

NCL SW-PU V is a ready-to-use hydrophobic hydroactive single-component flexible Polyurethane injection resin specially designed for permanent sealing of water leakages on vibratory structure. It is suitable for sealing all type of leaking concrete defects especially live cracks, movement joints and other imperfection that caused water ingress.

NCL SW-PU V is fast reacting to water. It is moisture sensitive and reacts rapidly in contact with water to foams a permanent flexible watertight seal. Due to its resilient flexibility, it allows and absorbs movement from concrete structure e.g. parking area, tunnel, track bed, under-construction building etc.

Once cured, NCL SW-PU V remain permanently flexible and forms an excellent water-impermeable barrier against moisture and water infiltration.
 

­­­­­­­­COMPOSITION

NCL SW-PU V is a single component Polyurethane Injection Resin based on methylene diphenol isocyanate and polyether polyol. It is ready-to-use, no mixing is required.
 

AREA OF APPLICATION
  • Live crack and Vibratory Structure
  • Tunnels and Subway
  • Movement Joint
  • Reinforced Concrete Wall & Slab
  • Basement and Diaphragm Wall
  • Dams
  • Sewerage Structure
  • Water Tank
  • Manhole & Wet Shaft
  • Brickwork
  • Void Filling, Rock and Soil Stabilization
  • Lift Pits
  • Curtain grouting
  • Other Specialized Applications
 

FEATURES & ADVANTAGES
  • No shrinkage
  • Penetration into cracks <200 microns
  • Excellent bonding
  • Provides permanent water-resistant barrier
  • Good chemical resistance & Non-corrosive
  • Unaffected by salts or contaminants in water
  • Non-toxic in cured form
  • Low viscosity
 
 
MATERIAL DATA


  UNIT PART A
Appearance - Yellowish
Viscosity mPa.s 500-600
Specific Gravity (at 25 °C) - 1.08
Flash Point °C >200
 

REACTION DATA


Resin:Water Ratio Cream Time (second) Rise time (second)
1:1 2 50
2:1 2 50
3:1 3 60
4:1 4 70
5:1 8 75
6:1 10 80
7:1 13 90
8:1 15 105
9:1 20 120
10:1 25 135
*The reaction time at 25 °C varies with the amount of water added. Result may vary depending on site condition.
 


APPLICATION GUIDELINE
NCL SW-PU V can be injected using single-line high-pressure injection machine e.g. NCL SWM1000, NCL SWM1100, NCL DHP-M1000 or NCL DHP-M2000. The injection resin is ready-to-use, no mixing is required. Refer to Method Statement for complete guide.
 

FINAL PRODUCT

The single component hydrophobic injection resin reacts, expands and foams to dense permanent flexible watertight seal in contact with moisture or water.
 

PACKAGING


Contents Weight  
Single Component NCL SW-PU V 10 kg  
 

STORAGE & HANDLING
It is recommended to keep container tightly closed in a cool (20 - 25°C), dry and well-ventilated place. Partly used drums/pails should be properly sealed to prevent ingress of moisture. To increase the material life expectancy, partially used drum/pail can be filled with nitrogen gas and sealed tightly to prevent contamination. When the material is stored properly, the shelf life is approximately twelve (12) months from the production date.

 
WASTE DISPOSAL

Waste disposal should be in accordance with all applicable local and national regulations. Kindly check with the local authorities on proper disposal method. Empty drums/pails should be punctured to clear the content. Care must be taken to prevent environmental contamination from the use of this material.

 
HEALTH & SAFETY
  • Ingestion: Do not induce vomiting. Treat symptomatically and get medical attention immediately.
  • Inhalation: Remove from exposure. If there is any difficulty in breathing, get medical attention immediately.
  • Skin Contact: Remove contaminated clothing. Immediately flush affected area thoroughly with mild soap and water.
  • Eye Contact: Immediately flood eyes with plenty of water for a minimum of 15 minutes holding the eyes open.
 
OTHER INFORMATION

All information contain herein was obtained from sources which we believe to be accurate and reliable. The information is subject to change without prior notice. However, it is provided without any warranty, expressed or implied, regarding its correctness. The information is provided for informational purposes and solely for customer’s consideration, investigation and verification. The statements in this information sheet are based on the best of our knowledge and experience. For this and other reasons, NCL Chemical & Equipment Sdn Bhd do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the material. However, we have no control over the method of application and the amount of care taken when using this product and therefore the liability of NCL Chemical & Equipment Sdn Bhd is limited to the quality of the delivered material.

Please leave your enquiry here, we will reply as soon as possible.
Name*  
Company Name  
Solutions Interested  
Quantity  
Email*  
Contact No.*  
Attachment  
*only support gif, jpeg, jpg, png, pdf
Messages*  

Switch to Mobile Version