NCL PU Grout Two-Component Rigid Injection Resin

Previous 2 / 2 Next

NCL PU Grout Two-Component Rigid Injection Resin  Two-Component Injection Resin NCL Injection Resin


PRODUCT DESCRIPTION
NCL PU GROUT is a low viscosity hydrophobic hydroactive two-part rigid Polyurethane injection resin designed to seal water infiltration through concrete deficiencies such as cracks, cold joint, segregation, porosity and other imperfections especially in underground infrastructure.

The curing profile of NCL PU GROUT is controllable by modifying the Hardener proportion to suit different site condition. Thus, NCL PU GROUT is suitable for sealing all type of concrete structure with various severity of leakages from minor moisture intrusion to gushing water.

Once cured, NCL PU GROUT forms a permanent watertight seal and excellent barrier against moisture and water seepage caused by hydrostatic pressure.


COMPOSITION
NCL PU GROUT is a low viscosity Two-part Polyurethane Injection Resin which consists of Part A – Resin/Base and Part B – Hardener. Part A and Part B are pre-mixed before application.


AREA OF APPLICATION

  • Reinforced Concrete Wall & Slab
  • Basement and Diaphragm Wall
  • Sewerage Structure
  • Water Tank
  • Manhole & Wet Shaft
  • Void Filling
  • Rock and Soil Stabilization
  • Lift Pits
  • Curtain grouting
  • Other Specialized Applications


FEATURES & ADVANTAGES

  • Low viscosity
  • Penetration into cracks <200 microns
  • Unaffected by salts or contaminants in water
  • Provides permanent water-resistant barrier
  • Good chemical resistance & Non-corrosive
  • Solvent and TDI free


MATERIAL DATA

  UNIT PART A PART B
Appearance - Dark Brown Liquid Yellowish Liquid
Viscosity mPa.s ~120 ~15
Specific Gravity (at 25 °C) - 1.16 1.02
Flash Point °C >210 >150
 

REACTION DATA


   Hardener Dosage (%) Cream Time (second) Rise time (second)
2 88 230
5 57 140
10 48 105
*The reaction time at 25 °C varies with the amount of hardener added. Result may vary depending on site condition.


APPLICATION GUIDELINE

NCL PU GROUT can be injected using single-line high-pressure injection machine e.g. NCL SWM1000, NCL SWM1100, NCL DHP-M1000 or NCL DHP-M2000. The resin and hardener shall be mixed homogeneously before use. Refer to Method Statement for complete guide.
 

FINAL PRODUCT

The hydrophobic injection resin first displace water then react, expand and foams to dense closed-cell rigid watertight seal in concrete structure.
 

PACKAGING


Contents Weight  
Part A : Resin 20 kg / 25 kg / 225 kg  
Part B : Hardener 1 kg / 5kg / 50 kg  
 

STORAGE & HANDLING

It is recommended to keep container tightly closed in a cool (20 - 25°C), dry and well-ventilated place. Partly used drums/pails should be properly sealed to prevent ingress of moisture. To increase the material life expectancy, partially used drum/pail can be filled with nitrogen gas and sealed tightly to prevent contamination. When the material is stored properly, the shelf life is approximately twelve (12) months from the production date.
 

WASTE DISPOSAL
Waste disposal should be in accordance with all applicable local and national regulations. Kindly check with the local authorities on proper disposal method. Empty drums/pails should be punctured to clear the content. Care must be taken to prevent environmental contamination from the use of this material.


HEALTH & SAFETY
  • Ingestion: Do not induce vomiting. Treat symptomatically and get medical attention immediately.
  • Inhalation: Remove from exposure. If there is any difficulty in breathing, get medical attention immediately.
  • Skin Contact: Remove contaminated clothing. Immediately flush affected area thoroughly with mild soap and water.
  • Eye Contact: Immediately flood eyes with plenty of water for a minimum of 15 minutes holding the eyes open.          

OTHER INFORMATION

All information contain herein was obtained from sources which we believe to be accurate and reliable. The information is subject to change without prior notice. However, it is provided without any warranty, expressed or implied, regarding its correctness. The information is provided for informational purposes and solely for customer’s consideration, investigation and verification. The statements in this information sheet are based on the best of our knowledge and experience. For this and other reasons, NCL Chemical & Equipment Sdn Bhd do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the material. However, we have no control over the method of application and the amount of care taken when using this product and therefore the liability of NCL Chemical & Equipment Sdn Bhd is limited to the quality of the delivered material.   

Please leave your enquiry here, we will reply as soon as possible.
Name*  
Company Name  
Solutions Interested  
Quantity  
Email*  
Contact No.*  
Attachment  
*only support gif, jpeg, jpg, png, pdf
Messages*  

Switch to Mobile Version